BIS Safety Software

Knuckle Boom Crane

Learn knuckle boom crane safety in this 60-minute online course: crane types, training requirements, Canadian standards, pre-shift inspection, stability and load charts, setup, safe lifting and emergency response. Earn a certificate of completion when you pass.

Knuckle boom crane operators work with one of the most adaptable lifting machines on Canadian worksites, and one of the most technically demanding. The articulating boom, shifting centre of gravity, and hydraulic systems create hazards that generic crane training does not address. This knuckle boom crane training course gives operators the specific knowledge they need to plan lifts, read load charts, rig loads correctly, and respond to emergencies before they escalate.

Designed for crane operators, riggers, and site supervisors who work with articulating cranes, this course covers pre-shift inspection, stability principles, rigging configurations, safe operating procedures, and emergency response. Everything needed to run a knuckle boom crane safely on any Canadian worksite.

Aperçu du cours

This knuckle boom crane course addresses every stage of safe articulating crane operation, from initial equipment identification through to emergency response. The modules cover the decisions you make before, during, and after every lift:

• Types of Knuckle Boom Cranes and Applications
• Training and Certification Requirements
• Applicable Canadian Standards
• Anatomy and Pre-Shift Inspection
• Stability, Centre of Gravity, and Load Charts
• Rigging Considerations
• Safe Operation Procedures
• Common Hazards
• Periodic Inspections
• Emergency and Rescue

Each module focuses on practical application. You learn what to check before a lift, how to interpret a load chart for an articulating boom, which rigging configuration suits a given load, and what to do when something goes wrong.

The course addresses the characteristics that separate knuckle boom cranes from other lifting equipment: the folding articulating joint, the hydraulic system, and the way the boom’s reach constantly shifts the machine’s centre of gravity.

Load charts, rigging configurations, emergency shutdown, and pre-shift checklists form the core of what you’ll master.

What You’ll Learn

This knuckle boom crane course builds your technical knowledge across the full operating sequence, from identifying components to executing an emergency response.

Equipment identification and pre-shift inspection

• Identify the major components of a knuckle boom crane and describe the function of each part in the lifting system.
• Apply a pre-shift inspection checklist to the crane before each shift, covering the hydraulic system, structural components, and controls.

Stability and load chart application

• Describe how the articulating boom affects the crane’s centre of gravity at different boom positions and extensions.
• Read and apply a load chart for an articulating crane to determine safe working loads across the full range of boom configurations.

Rigging selection and lift planning

• Recognize common rigging configurations and describe their capacity implications for a specific lift.
• Describe the correct setup sequence, lift planning steps, and shutdown procedures for a knuckle boom crane operation.

Hazard recognition and power line distances

• Identify common hazards associated with knuckle boom crane operation and describe the controls used to manage each one.
• Explain the minimum approach distances for overhead power lines when you operate an articulating crane.

Emergency procedures and assessment

• Describe emergency procedures for power line contact and tip-over response, and identify the correct sequence of actions for each scenario.
• Demonstrate retention of course content by achieving 80% on the final assessment to earn your certificate of completion.

Who Should Take This Course?

• Knuckle boom crane operators who are responsible for daily lifts, pre-shift inspections, and safe load handling on any worksite where an articulating crane is deployed.
• Riggers and signal persons who attach loads, select rigging hardware, and communicate with the operator during a lift. Load chart knowledge and rigging capacity are direct safety requirements in these roles.
• Site supervisors and lift planners who approve lift plans, assign operators, and are accountable when a lift goes wrong on their watch.
• Equipment owners and fleet managers who need documented knuckle boom crane operator training on file for every worker assigned to an articulating crane.
• Workers transitioning to crane operation who carry general construction or heavy equipment experience and are moving into a knuckle boom crane role for the first time.
• Safety officers and site coordinators who conduct site audits, review operator competency records, and need a working knowledge of articulating crane hazards and applicable Canadian standards.

Why Take This Course?

The articulating boom changes everything. Each time you extend or reposition the boom, the crane’s centre of gravity can shift significantly. An operator who cannot track that shift against the load chart can tip a crane without warning.

Emergency response is time-critical. Power line contact and tip-over scenarios are covered explicitly because the interval between contact and a fatal outcome can be seconds. You rehearse the correct response sequence here, so you execute it correctly under pressure on the job.

Safe operating practices for articulating cranes are woven throughout the course. You leave with a clear understanding of the principles that govern responsible crane use on Canadian worksites, from pre-lift planning to daily inspections. That knowledge shapes how you approach every lift and how you keep your crane in ready-to-work condition.

Undocumented training creates real risk. Employers who assign workers to knuckle boom cranes without a topic-specific training record carry operational and reputational exposure. Your certificate of completion gives both you and your employer a concrete record of what was covered and when.

Key Benefits

• Certificate of completion included. You receive a printable certificate to present to employers, site supervisors, or auditors as proof of knuckle boom crane operator training.
• Targets the failure points that cause crane incidents. The course addresses shifting centre of gravity, hydraulic system risks, and overhead power line proximity. These specific conditions lead to tip-overs and dropped loads.
• Completed in 60 minutes, entirely online. No travel, no classroom scheduling, and no lost shift time. You complete this self-paced knuckle boom crane course from any device, on your schedule.
• Load chart and rigging skills that transfer to every articulating crane job. Pre-shift inspection procedures, rigging selection, and load chart application apply on any worksite where a knuckle boom crane is deployed.
• Priced at $99.99 per enrolment. A fixed per-seat cost gives employers a predictable training budget line, with no variable expense from in-person instruction or third-party assessors.

Détails du cours

This knuckle boom crane online training course is available now through the BIS Safety Software store. You can manage and store completed training records using BIS Training Record Management to keep your operator documentation audit-ready.

• Durée 60 minutes
• Format: Online, self-paced, accessible from any device
• Pass mark: 80% on the final assessment
• Certificate: Certificate of completion included upon passing
• Price: $99.99 per enrolment

Foire aux questions

How long does the knuckle boom crane training course take to complete?

The knuckle boom crane course takes 60 minutes to complete. You work through it at your own pace and can access it from any device.

What score do I need to pass the knuckle boom crane course?

You need 80% on the final assessment to pass and receive your certificate of completion.

Is a certificate included when I complete the knuckle boom crane course?

Yes, the knuckle boom crane course includes a certificate of completion for every learner who achieves the 80% pass mark.

Who should take this knuckle boom crane training course?

This course is built for crane operators, riggers, signal persons, site supervisors, lift planners, and safety officers who work with or oversee articulating crane operations on Canadian worksites.

What does the knuckle boom crane course cover that general crane training does not?

This course focuses on the articulating crane specifically. You learn how to read a load chart for a variable-reach boom, select rigging configurations suited to knuckle boom lifts, and execute emergency procedures for power line contact and tip-over scenarios. Generic lifting equipment courses do not address this content.

How much does the knuckle boom crane online course cost?

The course is priced at $99.99 per enrolment, with a certificate of completion included when you pass.

Enrol in the Knuckle Boom Crane training course today and give your operators the load chart, rigging, and emergency response skills they need on every articulating crane job.

Cours de formation supplémentaires

Sexual Harassment and Discrimination Prevention

This tutorial provides an understanding of the legal responsibilities and potential penalties related to sexual harassment. It delves into the procedures to follow when...

Acheter maintenant | $69,99 CAD

Concepts de base de la sécurité au travail : En cas d'urgence

Un lieu de travail sûr n'est pas le fruit du hasard. La responsabilité de garantir un environnement de travail sûr et exempt de risques incombe...

Acheter maintenant | $49,99 CAD

Due Diligence for Supervisors

Our online Due Diligence for Supervisors course helps supervisors fulfill their safety responsibilities in the workplace by elucidating due diligence and outlining the steps...

Acheter maintenant | $79,99 CAD